background image

13 

< Note > 

 

This oil pressure warning indicator cannot detect oil deterioration. Change the engine oil 
periodically. (Refer to section “

8-1. Checking Engine Oil

”.) 

(3) WATER TEMP (Coolant Temperature) Warning Indicator (High Water Temp.) 

 

If the coolant temperature rises above 239 

°

F(115

) during operation, the WATER TEMP 

warning indicator illuminates, and the engine will be automatically stopped. If this occurs, hot 
steam will gush out of the coolant sub-tank. Check the coolant sub-tank coolant level after the 
generator cools and add coolant to the coolant sub-tank if it is insufficient. (Refer to section 

 

8-2. Checking Coolant

”.) If the coolant is at the specified amount, it is probable that the fan 

belt is loose or there is a coolant leak. Wait for the engine to cool down and inspect for these 
problems. 

< Note > 

 

The coolant temperature cannot be detected if the coolant level is excessively low. Always be 
sure to check the coolant level in the radiator coolant sub-tank before starting operation. 

(4) OVER SPEED (Engine Overspeed) Warning Indicator 

This generator is equipped with a function such that the engine is automatically stopped if an 
engine fault occurs causing the engine speed to increase excessively. If the engine speed 
rose above 4,140 rpm during operation, the OVER SPEED warning indicator illuminates, and 
the engine will be automatically stopped. If this occurs, it is probable that some malfunction 
has occurred in the engine. Contact authorized distributor where the generator was 
purchased. 

(5) SPILL CONTAINMENT (Spill Containment Amount) Checking Indicator 

The SPILL CONTAINMENT checking indicator illuminates if the liquid stored in the spill 
containment exceeds approximately about 4.2 gal (16 liters) during operation. If it illuminates, 
immediately stop the engine and flush the liquid stored in the spill containment.   
(Refer to section “

10. Inspection/Maintenance (10) Flushing Liquid in Spill Containment

”.)   

< Note > 

 

The engine may not be stopped only if the spill containment checking Indicator illuminates 
during operation. 

 

When the spill containment checking indicator illuminates during operation, stop the engine, 
check for fuel, oil and coolant leakage, and repair as necessary. 

 

Do not use the equipment with liquid accumulated in the spill containment. Drain the spill 
containment before using. 

 
 
 
 
 

 

  CAUTION: BURNS 

 

 

Do not open the radiator cap immediately after stopping the engine. Do so will result 
in hot steam gushing out. 

 

Hot steam gushes out from the coolant sub-tank if the generator overheats. Do not 
touch the coolant sub-tank. 

Summary of Contents for DGK15FL























































Reviews: