Shindaiwa DGK15FL Owner'S And Operator'S Manual Download Page 50 | Manualshive

Page: 50 / 54

background image

47

Problem

Suspected cause

Action

Overheated

1. Engine thermostat is defective
2. Water temp sensor is defective
3. Water temp meter is defective
4. Fan belt tension is weak
5. Coolant is insufficient
6. Radiator core is clogged

1.Contact our distributor to repair
2. Contact our distributor to repair
3. Contact our distributor to repair
4. Check/Adjust fan belt
5. Check/Add coolant
6. Clean radiator core

Black smoke
comes out from Muffler

1. Air filter element is clogged
2. Fuel injection nozzle is defective
3. Improper fuel is used

1. Check/Change air filter element
2. Contact distributor or dealer for repair
3. Change to clean fuel

White smoke
comes out from
Muffler

1. Too much or too little oil to cylinder
2. Water is interfused in fuel line
3. Fuel injection nozzle is defective
4. Coolant temperature is too low
5. Engine thermostat is defective

1. Contact distributor or dealer for repair
2. Drain water in fuel filter or fuel tank
3. Contact distributor or dealer for repair
4. Warm-up driving is needed
5. Contact distributor or dealer for repair

Pointer (hand) does not

move in voltage meter

1. Voltage meter is defective
2. AVR is defective
3. Disconnected circuit, loose terminal or

departed

4. Initial exciter is defective
5. Alternator is defective

1. Contact distributor or dealer for repair
2. Contact distributor or dealer for repair
3. Contact distributor or dealer for repair

4. Contact distributor or dealer for repair
5. Contact distributor or dealer for repair

Pointer (hand)
does not goes up
to the rated
voltage

1. Voltage meter is defective
2. AVR is defective
3. Voltage regulator dial is defective

1. Contact distributor or dealer for repair
2. Contact distributor or dealer for repair
3. Contact distributor or dealer for repair

Pointer exceeds
the rated voltage

1. Voltage meter is defective
2. AVR is defective
3. Improper load cable connection

1. Contact distributor or dealer for repair
2. Contact distributor or dealer for repair
3. Correctly set the connection location to

the receptacle

The voltage drops

drastically when

connecting to load

1. AVR is defective
2. Unbalanced loads sharing to each

terminal

3. The current of the used equipment

exceeds the rated current

4. Over load

5. Frequency is different

1. Contact distributor or dealer for repair
2. Balance the loads sharing to each

terminal

3. Change to a device with an available

capacity

4. Decrease the loads to meet the rated

output

5. Set the specific frequency

Cannot turn the
breaker to ON

1. The Main breaker positions at between

ON and OFF

2. Short circuit on the load

1. Once turning the lever to OFF, turn it to

ON

2. Check the load circuit

«
...
48
49
50
51
52
...
»

Summary of Contents for DGK15FL























































Reviews:

No comments

Related manuals for DGK15FL

Brand: Denver Pages: 60

Brand: IVIEW Pages: 32

Brand: Takstar Pages: 40

Brand: Fujitsu Pages: 17

J Adapter Class Generator

Brand: Fujitsu Pages: 98

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 3

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 2

Brand: Philips Pages: 3

Brand: Philips Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands