Shindaiwa DGA12DM Owner'S And Operator'S Manual Download

Page: 26 / 52

Radiator Cap Cover

Radiator Cap

Inlet

Radiator Plate



Viscosity and temperature

-30

-15

25 30

SAE10W

SAE30

SAE40

SAE20/20W

SAE10W-30

SAE15W-40/20W-40

Tem

(C)

(2) Replacing Engine Oil Volume

(Unit: Liter)

Lubrication Oil (including the oil in filter)

7.3 (0.3)

Value in ( ) shows the oil in filter

8-2. Checking Coolant / Water

WARNING : Injuries



Before performing any equipment check or maintenance, stop the engine,

and turn the Power Switch to the OFF position.

CAUTION : Burns



Do not open the radiator cap while operating this equipment or

immediately after stopping the equipment, to avoid sustaining burns from
hot vapor or water.



Do not touch the engine and muffler during operation and immediately

after stopping the equipment, for the temperature can reach extremely
high levels.

Check the radiator and coolant reservoir tank for water and add water in case of

shortage.

(1) Checking Radiator / Adding water

Remove the radiator plate and open the

radiator cap cover.

Remove the radiator cap.

Fill up water to the radiator water inlet top.

Reinstall the cap and tighten it.

Close the radiator cap cover and reinstall the radiator plate.

Summary of Contents for DGA12DM





















































Search results

Summary of Contents for DGA12DM

Reviews:

Related manuals for DGA12DM

Brands by name

Popular brands

Shindaiwa DGA12DM, Owner'S And Operator'S Manual

Search results

Summary of Contents for DGA12DM

Reviews:

Related manuals for DGA12DM

Brands by name

Popular brands