background image

 

26 

Fixing Clamp 

 

-Post 

 

+Post 

 

8-6. Checking Battery 

 

CAUTION : Injuries to eyes and skin 

 

  Battery fluid contains diluted sulfuric acid.    Avoid contact with eyes, skin 

or on clothing.    If the acid comes in contact, especially with eyes, 
flush with a lot of water, and contact physician or doctor immediately. 

 

CAUTION : Explosion 

 

  When the liquid level is below the LOWER level, never use the equipment 

nor recharge battery. 

  Battery may emit some combustible gas, so keep it away from fire and 

sparks. 

 

 

Check the fluid level. If the level is near or lower than the LOWER LEVEL, add 

distilled water until the fluid level reaches the UPPER LEVEL limit. 

 

Make sure that the battery cables are firmly secured to the posts. Tighten the clamps 

more if necessary. 

< Note >

 

  Check the hydrometer of the battery fluid. If it falls below 1.23, the battery requires 

recharging. Please call our authorized distributor or our engineering section. 

 

Replacing the Battery 

 

Remove the clamp and cable from negative 

(-)

 

post from the battery (always remove negative 
side first).

 

 

 
Remove  the  battery  fixing  clamp. 
 
 
Remove  the  cable  from  positive 

(+)

 
 
Remove  the  battery  from  the  seat. 
 

 

Reinstall a new Battery in the reverse order (always install the cable to the 

positive (+) 

post of 

the new Battery first). 

 

 
 

 

 

 

 

 

 

 

 

Summary of Contents for DGA12DM





















































Reviews: