background image

24

ADDITIONAL PROBLEMS

Poor acceleration.

Clogged air fi lter.

Clogged fuel fi lter.

Lean fuel/air mixture.

Idle speed set too low.

Ignition switch turned off.

Fuel tank empty.

Water in the fuel.

Clogged fuel fi lter.

Shorted spark plug or loose terminal.

Ignition failure.

Piston seizure.

Ground (stop) wire is disconnected, 

or switch is defective.

Overheating due to incorrect spark plug.

Overheated engine.

Clean the air fi lter.

Replace the fuel fi lter.

Consult with an authorized Shindaiwa

servicing dealer.

Adjust idle. Check 

Specifi cations

 page for correct idle speed.

Reset the switch and re-start.

Refi ll with fresh, clean unleaded gasoline with a pump octane 

of 89 or higher mixed with an air cooled engine oil that 

meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils 

at 50:1 gasoline/oil ratio.

Replace fuel fi lter.

Clean or replace spark plug. Check the 

Specifi cations

 section 

for the correct plug and gap for your unit.  Tighten

the terminal.

Replace the ignition unit.

Consult with an authorized Shindaiwa

servicing dealer.

Test and replace as required.

Replace the spark plug. Check the Specifi cations section for 

the correct plug and gap for your unit. Restart.

Idle engine until cool.

Symptom

Possible Cause

Remedy

Engine stops abruptly.

Engine diffi cult to shut off.

Troubleshooting Guide 

(continued)

Engine idle too high.

Broken clutch spring or worn clutch 

spring boss.

Loose attachment holder.

Warped or damaged attachment.

Loose gearcase.

Cutting attachment 

moves at engine idle.

Excessive vibration.

Cutting attachment will not 

move.

Adjust idle. Check Specifi cations page for correct idle 

speed.
Replace spring/shoes as required, check idle speed.

Inspect and re-tighten holders securely.

Inspect and replace attachment as 

required.
Tighten gearcase securely.

Bent main shaft/worn or damaged bushings.

Shaft not installed in powerhead or gearcase.

Broken shaft.
Damaged gearcase.

Inspect and replace as necessary.

Inspect and reinstall as required.

Idle set too high.

Adjust idle. Check Specifi cations page for correct 

idle speed.

Engine will not idle 

down.

Engine has an air leak.

Consult with an authorized Shindaiwa servicing 

dealer.

Consult with an authorized Shindaiwa servicing 

dealer.

Summary of Contents for C282

































Reviews: