background image

21

IMPORTANT!

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is 

added.

Loading Trimmer Line 

1.  Cut one piece of line to recommended length.
2.  Align arrows on top of knob with openings in eyelets.
3.  Insert one end of trimmer line into an eyelet, and push line 

equal distance through trimmer head.  

4.  Hold trimmer head while turning knob clockwise to wind 

line onto spool until about 5” (13 cm) of each line remains 

exposed. 

  

Trimmer head is now fully loaded and ready for operation.

.080 (2.0 mm) dia. - 20’ (6 m)

.095 (2.4 mm) dia. - 14’ (4 m)

.105 (2.7 mm( dia. - 10’ (3 m)

1

2

3

4

 

Remove the spark plug and pour 

about 1/4 oz. of 2-cycle mixing oil 

into the cylinder through the spark 

plug hole. Slowly pull the recoil 

starter 2 or 3 times so oil will evenly 

coat the interior of the engine. Rein-

stall the spark plug.

 

Before storing the unit, repair or 

replace any worn or damaged parts.

 

Remove the air cleaner element from 

the carburetor and clean it thor-

oughly with soap and water. Let dry 

and reassemble the element.

 

Store the unit in a clean, dust-free 

area.

Long Term Storage

Whenever the unit will not be used for 30 

days or longer, use the following proce-

dures to prepare it for storage:

 

Clean external parts thoroughly.

 

Drain all the fuel from the fuel tank.

 

Remove the remaining fuel from the 

fuel lines and carburetor. 

1.  Prime the primer bulb until no more 

fuel is passing through.

2.  Start and run the engine until it 

stops running.

3.  Repeat steps 1 and 2 until the engine 

will no longer start.

  CAUTION!

Gasoline stored in the carbure-

tor for extended periods can cause 

hard starting, and could also lead to 

increased service and maintenance 

costs.

IMPORTANT!

All stored fuels should be stabilized with 

a fuel stabilizer such as STA-BIL™.

NOTE:

Damage resulting from stale or con-

taminated fuel is not covered by the 

Shindaiwa warranty policy.

Wear Indicators

Wear Indicators

Indicadores de desgaste

Indicadores de desgaste

Indicateurs d’usure

Indicateurs d’usure

IMPORTANT!  

When the wear indicators located at the bottom of the Speed-Feed head are worn smooth, replacement of the cover or the 

entire Speed-Feed head is required.

NOTE: 

Trimmer head is pre-wound with .095” (2.4mm) 

Silentwist™ trimmer line.

Summary of Contents for C282

































Reviews: