SHENZHEN FANHAI SANJIANG ELECTRONICS JB-QBL-9116E User Manual Download Page 10

Page: 10 / 66

①

Indication function

：

Figure 3-2 Indication function zone

No.

Silk-screen

characters

Light

color

Function description

POWER

Green

The indicator light will be on when the mainboard is normally

supplied by the host (or standby power supply).

The illuminating of the indicator

light does not indicate other system components
(except for the mainboard) are normally supplied, that
is, the indicator light will be on as long as the power
supply of the mainboard is normal.

FIRE

Red

The indicator light is on when the system detects any fire

alarm.

FAULT

Yellow

The indicator light will be lit when the system detects any fault

alarm (regardless of fault types).

START

Red

The indicator light will be lit if the system has sent out a

linkage request of a certain module.

SYSTEM

FAULT

Yellow

The indicator light will be lit when the machine is in fault or the

system is not operating as expected.

FDBK

Red

The indicator light will be lit if the system has received a

linkage feedback of a certain module.

POWER

FAUIT

Yellow

The indicator light will be lit when the system detects the alarm

of power supply (regardless of fault type).

LINKAGE

DELAY

Red

The indicator light has been lit up until the end of linkage delay.

H/S

FAULT

Yellow

The indicator light will be lit when the horn/strobe alarm

apparatus or far sound equipment (alarm bell) in the system
goes wrong.

COMM.

Red

The indicator light will be flash when the CAN communication

or Ethernet communication is normally.

SYSTEM

TEST

Yellow

The indicator light will be lit when the machine carries out

self-test or single-point test and will go off after self-test
completion.

NETWORK

Red

The indicator light is temporarily useless.

Summary of Contents for JB-QBL-9116E



































































Search results

Summary of Contents for JB-QBL-9116E

Reviews:

Related manuals for JB-QBL-9116E

Brands by name

Popular brands

SHENZHEN FANHAI SANJIANG ELECTRONICS JB-QBL-9116E, User Manual

Search results

Summary of Contents for JB-QBL-9116E

Reviews:

Related manuals for JB-QBL-9116E

Brands by name

Popular brands