E-ZOOM Functions
E-19
E-ZOOM/PANNING Function
This projector has an E-ZOOM (640 x 480 dot, NTSC, etc.)
mode which enlarges the display when inputting an image of
less than 800 x 600 dot in resolution. There is also a
PANNING mode which allows an 800 x 600 dot display when
there is no compression.
1. Press the MENU button to select
E-ZOOM mode.
Press the MENU button. While the MENU screen is displayed,
press the ADJUSTMENT
ƒ
/
∂
buttons to select IMAGE ADJ.
Then press the MENU button to display the IMAGE ADJ.
screen as shown. Press the ADJUSTMENT
ƒ
/
∂
buttons to
select E-ZOOM/PAN, and press the ADJUSTMENT
ß
/
©
but-
tons to select ON. Press the MENU button. When the VGA
(640 X 480 dot), Mac 16" (832 x 624) signal is input, the
projector will enter E-ZOOM mode.
Note:
• The E-ZOOM/PANNING button on the side of the projector
can also be used to display E-ZOOM mode. Press this
button while the on-screen display (below) is displayed to
turn E-ZOOM ON and OFF.
E-ZOOM (ON):
The screen image will be enlarged or
reduced to 800 x 600 dot.
E-ZOOM (OFF):
The resolution of the image does not
change. Use the ADJUSTMENT
ƒ
/
∂
and
ß
/
©
buttons for panning when a
Mac 16" (832 x 624 dot) image is input.
E-ZOOM (---):
No input
Notes:
• Select ON 1 or ON 2 to set the status for either a 640
2
400
dot image or 640
2
350 dot image in the E-ZOOM mode.
• In the E-ZOOM mode, an enlarged display increases the
amount of data processed on the screen and a
compressed image decreases the number of lines
displayed, which may make characters difficult to read.
2. Press the E-ZOOM/PANNING button on
the remote control.
The E-ZOOM/PANNING button on the remote control can be
used to select E-ZOOM and NO E-ZOOM (PANNING) modes.
Note:
• In SVGA INPUT mode, (---) appears, indicating that E-
ZOOM function does not operate in this mode.
3. Press the MENU button anytime to exit
E-ZOOM mode.
PANNING Function: Mac 16" (832 x 624)
(NO E-ZOOM)
In NO E-ZOOM mode, the ADJUSTMENT
ƒ
/
∂
and
ß
/
©
buttons can be used to move the image of the display within
the 800 X 600 dot screen.
• Press any one of the ADJUSTMENT
ƒ
/
∂
and
ß
/
©
buttons
to begin operation of this function.
(Remote control)
• Press the ADJUSTMENT
ß
/
©
buttons first, then use the
ADJUSTMENT
ƒ
/
∂
and
ß
/
©
buttons to change the size
of the display.
• If the ADJUSTMENT
ƒ
/
∂
buttons are pressed first, the
volume display will appear on the screen.
Notes:
• E-ZOOM and PANNING functions do not operate in SVGA
(800 x 600 dot), PAL, SECAM INPUT mode.
• If the input signal is changed in RGB input mode, E-ZOOM
and PANNING functions may not operate. Should this
occur, press the MENU button. The projector will verify the
input signal, then the E-ZOOM and PANNING functions will
operate.
• When connecting to some SVGA notebook computers,
SVGA signals may be output even in VGA mode, thus
disabling the E-ZOOM function.
I M A G E A D J .
I N P U T D I S P L A Y ( O N )
: S E L . : A D J . M E N U : E N D
R E V E R S E ( O F F )
B L U E S C R E E N ( O F F)
E - Z O O M / P A N ( O F F )
E-ZOOM (OFF)
E-ZOOM (ON)
1
2
On-Screen Display
X G - E 6 9 0 U B ( E ) / p p . 1 7 - 2 1
G. K . A s s o c i a t e s , To k y o
1 9 9 8 / 5 / 2 1
