background image

Advanced Features
Playback

Advanced Features

 74

Audio Dubbing
Feature

Available mode:

Tape Playback

You can add narration to recordings made
with this camcorder, while preserving the
original audio and video recordings.

Microphone for Audio Dubbing

You can use the built-in stereo microphone
to record narration.

Notes:

• Audio dubbing does not function through the

DV terminal.

• You cannot use audio dubbing with

recordings made in LP mode.

• You cannot use the built-in stereo microphone

for audio dubbing when the audio/video/S-
video cable is connected.

• You cannot use the zoom microphone to

record narration.

Audio Recording

In normal recording mode

12-bit audio recording

The audio is recorded in stereo on Audio 1.

Audio 1:

 Stereo (left and right) sound

Audio 2:

 No audio

16-bit audio recording

The audio is recorded in stereo with the left
and right sound on two separate channels.

Audio 1:

 Left sound

Audio 2:

 Right sound

In Audio Dubbing mode

12-bit audio recording

The dubbed audio is recorded on Audio 2.

Audio 1:

 Original stereo (left and right)

sound

Audio 2:

 Dubbed stereo (left and right)

sound

16-bit audio recording

The dubbed audio is recorded on Audio 2
over the original right sound. Both dubbed
and original sounds are mono.

Audio 1:

 Original left sound

Audio 2:

 Dubbed sound

Notes:

• You can select the 12-bit or 16-bit audio

recording mode by performing the procedure
on page 47.

• You can perform audio dubbing, such as

music, on Audio 2 if you connect another
source via the AV cable. If the audio to be
dubbed was recorded in 12-bit audio
recording mode, it can be recorded on Audio
2 in stereo sound.

Built-in stereo

microphone

VL-Z500E-E-066-075

04.2.17, 9:22 AM

74

Summary of Contents for ViewcamZ VL-Z500E-S
































































































































Reviews: