Sharp ViewcamZ VL-Z500E-S Page 20 Operation Manual Download

Page: 20 / 127

Preparation

Inserting and
Removing a Cassette

Inserting

Attach the power source to the
camcorder, then slide and hold the
cassette compartment door release
as you open the cassette compart-
ment door.

• After confirmation sound, the

cassette holder extends and opens
automatically.

Insert a commercially available Mini
DV cassette fully with the window
facing outwards, and with the erasure
protect tab facing upwards.

Press the “PUSH” mark gently until
the cassette holder clicks into place.

• The cassette holder retracts

automatically.

Wait for the cassette holder to fully
retract. Close the compartment door
by pressing its centre until it clicks
into place.

Removing

Perform step 1 above, then take out the
cassette.

Notes:

• Do not try to close the cassette compartment

door while the cassette holder is extending or
retracting.

• Be careful not to get your fingers caught in

the cassette holder.

• Do not apply force to the cassette holder

except when pressing the “PUSH” mark to
close it.

• Do not tilt the camcorder or hold it upside

down when you are inserting or removing a
cassette. It may damage the tape.

• Remove the cassette if you will not use the

camcorder for a long period of time.

• If you do not correctly close the cassette

holder in step 3, the cassette protection
mechanism of the camcorder might eject the
cassette. If this happens, repeat the insertion
procedure.

• Do not attempt to pick up the camcorder by

the cassette compartment door.

• If the battery power is too low, you may not

be able to eject the cassette. Replace the
battery pack with a fully charged one.

• You can only use Mini DV cassettes. Large

DV cassettes cannot be used. Be sure to use
Mini DV cassettes with the

mark.

• See pages 99 and 100 for more information

on the video cassette tapes intended for use
with this camcorder.

SA VE

Cassette compartment door release

“PUSH” mark

Erasure protect tab

VL-Z500E-E-006-021

04.2.17, 9:17 AM

Summary of Contents for ViewcamZ VL-Z500E-S
































































































































Search results

Summary of Contents for ViewcamZ VL-Z500E-S

Reviews:

Related manuals for ViewcamZ VL-Z500E-S

Brands by name

Popular brands

Sharp ViewcamZ VL-Z500E-S, Operation Manual

Search results

Summary of Contents for ViewcamZ VL-Z500E-S

Reviews:

Related manuals for ViewcamZ VL-Z500E-S

Brands by name

Popular brands