Sharp UX-A260 Operation Manual Download

Page: 81 / 108

8. Mai

tenanc

8. Maintenance

Print head

Clean the print head frequently to ensure optimum printing performance.

Note:

Remove the paper from the paper tray before cleaning the print head.

Unplug the power cord, and open the
operation panel (press

➊

Take the imaging film out of the print
compartment and place it on a sheet of
paper.

Wipe the print head with isopropyl
alcohol or denatured alcohol.

Caution!

•

Do not use benzene or thinner. Avoid
touching the print head with hard
objects.

•

The print head may be hot if your fax
machine has just received a large
number of documents. If this is the
case, allow the print head to cool prior
to cleaning.

Print head

all.book

Page 79

Wednesday, June 4, 2003

1:07 PM

Summary of Contents for UX-A260













































































































Search results

Summary of Contents for UX-A260

Reviews:

Related manuals for UX-A260

Brands by name

Popular brands

Sharp UX-A260, Operation Manual

Search results

Summary of Contents for UX-A260

Reviews:

Related manuals for UX-A260

Brands by name

Popular brands