Sharp UX-A260 Operation Manual Download

Page: 15 / 108

Loading the Imaging Film

1. Ins

tal

lati

Loading the Imaging Film

Your fax uses a roll of imaging film to create printed text and images. The print
head in the fax applies heat to the imaging film to transfer ink to the paper.
Follow the steps below to load or replace the film.

Remove the paper from the paper tray
and open the operation panel (press

➊

Remove the used film and
empty spool.

Remove the two green gears from the
spools.
DO NOT DISCARD THE TWO GREEN
GEARS!

When replacing the film,
use a roll of Sharp

UX-

5CR

imaging film. One

roll can print about 150
letter-size pages.

The initial starter roll of
imaging film included with
your fax can print about
30 letter-size pages.

If you are loading the imaging film for
the first time, go to Step 4.

Use only Sharp Genuine
Supplies with this logo:

all.book

Page 13

Wednesday, June 4, 2003

1:07 PM

Summary of Contents for UX-A260













































































































Search results

Summary of Contents for UX-A260

Reviews:

Related manuals for UX-A260

Brands by name

Popular brands

Sharp UX-A260, Operation Manual

Search results

Summary of Contents for UX-A260

Reviews:

Related manuals for UX-A260

Brands by name

Popular brands