Sharp UX-A260 Operation Manual Download Page 35

Page: 35 / 108

Transfer Function

2. Ans

ing

Mac

ine

Recording the transfer message

The transfer message plays when you answer the telephone, and informs you
that the call is a transfer call. It can be up to 15 seconds long. To record a
transfer message, follow the steps below. The following is an example:

“Hello. This is a transfer call for (YOUR NAME). Enter your remote code
number now.”

Press

once and

twice.

Press

once.

Lift the handset.

(If you have already recorded a
message, you can press

listen to the message, or press

to delete the message.)

Press

and speak into the handset to record the message.

•

The transfer message can be up to 15 seconds long. While recording, the
display will show the time left to record.

When finished, replace the handset or press

REC/

MEMO

PLAY/

HOLD

DELETE

START/MEMORY

STOP

Display:

OGM2(TRANSFER)

all.book

Page 33

Wednesday, June 4, 2003

1:07 PM

Summary of Contents for UX-A260













































































































Search results

Summary of Contents for UX-A260

Reviews:

Related manuals for UX-A260

Brands by name

Popular brands

Sharp UX-A260, Operation Manual

Search results

Summary of Contents for UX-A260

Reviews:

Related manuals for UX-A260

Brands by name

Popular brands