Sharp MX-M550N Operation Manual Download Page 76

Page: 76 / 200

FINISHER AND SADDLE STITCH FINISHER

3-12

Remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

Close the entrance cover of the saddle
stitch unit.

Turn the right-hand knob

counter

clockwise. Then, push the left-hand knob

and turn it clockwise.

Remove any paper misfed on the exit side
of the saddle stitch unit.

Be careful not to tear the
misfed paper during
removal.

Open the exit cover of the saddle stitch
unit and remove any misfed paper.

Be careful not to tear the
misfed paper during
removal.

Close the exit cover of the saddle stitch
unit.

Close the lower cover of the saddle stitch
finisher.

Close the front cover of the inserter (only
when an inserter is installed).

■

When a punch module is installed

Open the cover of the hole punch module.

Rotate the green knob until the arrow is
within the range (A) on the label, and
remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

Close the cover of the hole punch module.

Push the finisher back against the main
unit.

(A)

Summary of Contents for MX-M550N









































































































































































































Search results

Summary of Contents for MX-M550N

Reviews:

Sharp MX-M550N, Operation Manual, Page: 76 / 200

Search results

Summary of Contents for MX-M550N

Reviews: