manualshive.com logo in svg

Sharp MX-M550N, Operation Manual, Page: 58 / 200

Share
Download
Sharp MX-M550N Operation Manual Download Page 58

MISFEED REMOVAL

2-28

■

Misfeed in the bypass tray

1

Remove the misfed paper from the bypass
tray.

Be careful not to tear the
misfed paper during
removal.

2

If you did not find a misfeed in step 1, open
the side cover and remove the misfeed.

3

Gently close the side cover.

4

Remove tray 1 - tray 2.

Grasp the finger hold
and gently open the unit.
Pull the tray all the way
out until it stops.

5

Remove the misfed paper.

Check the  paper
transfer unit inside the
tray and remove any
misfed paper.

6

Gently close paper tray 1 - tray 2.

Push the tray all the way
back in.
Make sure that the
misfeed message no
longer appears (the
normal message display
should appear).

NOTE

If a misfeed occurs during printing from the bypass
tray while paper is being loaded in tray 1 - tray 2,
push tray 1 - tray 2 back in to close it, and then pull
the tray out again.

Summary of Contents for MX-M550N









































































































































































































Reviews:

No comments