manualshive.com logo in svg

Sharp MX-M550N, Operation Manual, Page: 75 / 200

Share
Download
Sharp MX-M550N Operation Manual Download Page 75

FINISHER AND SADDLE STITCH FINISHER

3-11

3

Removing a misfeed

When a misfeed occurs, remove the misfed paper as explained below.

■

General procedure for the finisher and saddle stitch finisher

1

Gently move the finisher/saddle stitch
finisher away from the machine while
pressing the button.

When an inserter is
installed,  separate the
inserter from the
machine while pressing
on the inserter button.

2

Remove the misfed paper from the main
unit.

After removing the
misfed paper, perform
steps 1 and 3 on page 2-
24 to reset the machine.

3

Open the upper cover of the finisher/
saddle stitch finisher.

When an inserter is
installed, lift the tray of
the inserter.

4

Lift knob 

(A)

 (See the step 3 figure), then

remove any misfed paper.

Be careful not to tear the
misfed paper during
removal.

5

Lift knob 

(B)

 (see the illustration in step 4)

and remove any misfed paper.

Be careful not to tear the
misfed paper during
removal.

6

Remove any misfed paper from the paper
exit area.

Be careful not to tear the
misfed paper during
removal.

7

Close the upper cover of the finisher/
saddle stitch finisher.

■

When a saddle stitch finisher is installed

8

Open the front cover of the inserter (only
when an inserter is installed).

9

Open the lower cover of the saddle stitch
finisher.

10

Open the entrance cover of the saddle
stitch unit.

(A)

(B)

Summary of Contents for MX-M550N









































































































































































































Reviews:

No comments