manualshive.com logo in svg

Sharp MX-M550, Operation Manual, Page: 38 / 200

Share
Download
Sharp MX-M550 Operation Manual Download Page 38

LOADING PAPER

2-8

Loading paper in paper tray 5 (optional large capacity tray
AR-LC7)

An optional large capacity tray (AR-LC7) is available for the machine. The AR-LC7 can hold up to 3000 sheets of 20
lbs. (80 

g

/m

2

) paper. (See  the following "Specifications" for the types of paper that can be used in the large capacity

tray.)
When installed, the AR-LC7 operates as "Tray 5". The AR-LC7 cannot be used together with the AR-LC6  described
on page 2-7.

■

Part names

■

Specifications

* The indicated sizes of plain paper can be used.

When using the AR-LC7, refer also to "More
information on plain paper" on page 2-13.

Specifications are subject to change for improvement
without notice.

NOTES

●

If you wish to change the paper size, please consult
your dealer (the paper size must be changed by a
service technician).

●

Do not use curled or folded paper. This may cause
misfeeds.

●

When the tray has been pulled out, do not place
heavy objects on the tray or press down on the tray. 

●

Do not place any objects on the large capacity tray
or use it instead of a chair or step. This may
damage the tray and interfere with the use of the
bypass tray.

Operation button / 
Indicator

To load paper in the tray,
press this button, wait until
the indicator turns off, and
then pull the tray out.

Top cover

Open this cover to
remove a misfeed.

Paper size display

●

Load paper in the tray with the print side face up.
However, if the paper type is "PRE-PRINTED" or
"LETTER HEAD", load the paper with the print side
face down*.

* If the two-sided function is disabled using

"DISABLING OF DUPLEX" in the administrator
settings (page 11 of the administrator settings
guide), load the paper face up.

Name

Large capacity tray (AR-LC7)

Paper sizes*

11" x 17" (A3), 8-1/2" x 14" (B4),
8-1/2" x 11" (A4), 8-1/2" x 11"R (A4R)
Paper weight 16 to 28 lbs. (60 to 105

g

/m

2

)

Number of
paper trays
/Paper capacity

One tray 3000 sheets (20 lbs. or 80

g

/m

2

)

Power supply

Supplied from the machine

Dimensions

27-5/32" (W) x 23-7/64" (D) x
20-17/32" (H) (690mm (W) x 587mm
(D) x 521.5mm (H))

Weight

Approx. 110 lbs. (Approx. 50 k

g

)

dragonII_copy_sec.book  8 ページ  ２００６年１０月１８日　水曜日　午後７時３９分

Summary of Contents for MX-M550









































































































































































































Reviews:

No comments