manualshive.com logo in svg

Sharp MX-M550, Operation Manual, Page: 136 / 200

Share
Download
Sharp MX-M550 Operation Manual Download Page 136

SPECIAL MODES

5-28

1

Touch the [TAB COPY] key in the special
modes screen (2nd screen).

The TAB COPY setting
screen will appear. A
tab copy icon (

) will

also appear in the
upper left corner of the
screen to indicate that
the function is turned
on.

2

If necessary, set the image shift width (tab)
and touch the [OK] key.

Set the image shift
width (tab) with the

 and 

 keys.

The width can be set
from 0 to 5/8" (0 to 20
mm) in increments of 1/
8" (1 mm).

3

Touch the [OK] key in the special modes
screen.

You will return to the main screen of copy mode.

4

Load tabbed paper in the bypass tray.

Place the tabbed paper
so that the edges with
the tabs are the trailing
edge.

To use tab paper in tray
3, set the paper type
setting of tray 3 to "TAB
PAPER" in the tray
settings of the system
settings (page 2-14).

To load tabbed paper in

tray 3, see "Loading tabbed paper" on page 2-6.

5

Select "TAB PAPER" for the paper type
setting.

The paper type setting is explained in “Setting the
paper type and paper size” (page 2-14).
If you are using tray 3, see “Setting the paper size
when a special size is loaded” (page 2-17).

To display the special modes screen...

See "General procedure for using special
functions" on page 5-2.

NOTE

The width of the tabbed paper can be up to 8-1/2" x
11" width (8-1/2") + 5/8" (or A4 width (210 mm) + 20
mm).

SPECIAL MODES

COVERS/INSERTS

TRANSPARENCY

INSERTS

TAB COPY

BOOK COPY

IMAGE SHIFT

1/2

OK

OK

CANCEL

(0  5/8)
inch

About the steps that follow

If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 4-
13.

When performing tab copying with a right
binding

If you are using left-binding tabbed paper for a right
binding, either stack the sheets in reverse order or
scan the originals in reverse order.(See the table on
the previous page.

)

To cancel the tab copy function, touch the [CANCEL]
key in the tab copy setting screen (the screen of step
2).

dragonII_copy_sec.book  28 ページ  ２００６年１０月１８日　水曜日　午後７時３９分

Summary of Contents for MX-M550









































































































































































































Reviews:

No comments