manualshive.com logo in svg

Sharp MX-M550, Operation Manual, Page: 13 / 200

Share
Download
Sharp MX-M550 Operation Manual Download Page 13

1-1

CHAPTER 1

BEFORE USING THE 

PRODUCT

This chapter contains basic information that should be read before using
the product.

Page

INTRODUCTION..................................................................................... 1-2

MAIN FEATURES ................................................................................... 1-3

PART NAMES AND FUNCTIONS........................................................... 1-10

●

Exterior............................................................................................ 1-10

●

Interior ............................................................................................. 1-11

●

Operation panel............................................................................... 1-13

●

Touch panel..................................................................................... 1-14

TURNING THE POWER ON AND OFF.................................................. 1-17

AUDITING MODE ................................................................................... 1-18

●

Using the machine when the auditing mode is enabled.................. 1-18

dragonII_copy_sec.book  1 ページ  ２００６年１０月１８日　水曜日　午後７時３９分

Summary of Contents for MX-M550









































































































































































































Reviews:

No comments