manualshive.com logo in svg

Sharp MX-M550, Operation Manual, Page: 156 / 200

Share
Download
Sharp MX-M550 Operation Manual Download Page 156

6-2

USER MAINTENANCE

To ensure good service from this product over a long period of time, it is recommended that the following
maintenance procedures be performed on a regular basis.

Cleaning the document glass and the automatic document
feeder

If the document glass, document cover or automatic document scanning unit have dirty spots, these spots will form
lines in scanned images. These will show up as defects when the images are printed. Always keep these parts clean.

Wipe with a clean, soft cloth. If necessary, moisten the
cloth with water or a small amount of neutral detergent.
When finished, wipe dry with a clean cloth.

If black or white stripes
appear on printed
images of originals that
were fed through the
automatic document
feeder, wipe the long
narrow glasses in the

scanning unit (

 and 

 in the illustration).

CAUTION

Do not use flammable spray to clean the machine. If gas from the spray comes in contact with hot electrical
components or the fusing unit inside the machine, fire or electrical shock may result.

NOTE

When cleaning, do not use thinner, benzene, or similar volatile cleaning agents.

Example of dirty print image

Black stripes

White stripes

dragonII_copy_sec.book  2 ページ  ２００６年１０月１８日　水曜日　午後７時３９分

Summary of Contents for MX-M550









































































































































































































Reviews:

No comments