manualshive.com logo in svg

Sharp MX-M550, Operation Manual, Page: 14 / 200

Share
Download
Sharp MX-M550 Operation Manual Download Page 14

1-2

INTRODUCTION

Thank you for purchasing a SHARP digital multifunction copier.
Please read this manual before using the machine. In particular, be sure to read "INSTALLATION REQUIREMENTS"
before using the machine.
Please keep this manual close at hand for reference whenever necessary.
This manual provides general information on using the machine, such as routine maintenance and how to load paper
and remove misfeeds. It also explains how to use the copier and document filing functions.
Separate manuals have been provided for the fax function, printer function, and network scanner function.

■

Original and paper sizes

This machine allows use of standard sizes in both the inch and AB systems.
These are shown in the tables below.

■

The meaning of "R" in original and paper size indications

Some original and paper sizes can be placed in either the portrait or landscape orientations. To differentiate
between landscape and portrait, the landscape orientation size indication will contain an "R". These are indicated
as 8-1/2" x 11"R, 5-1/2" x 8-1/2"R, A4R, B5R, etc. Sizes that can be placed only in the landscape orientation (11"
x 17", 8-1/2" x 14", 8-1/2" x 13", A3, B4) do not contain the "R" in their size indication.

Sizes in the inch system

Sizes in the AB system

11" x 17" (LEDGER)

A3

8-1/2" x 14" (LEGAL)

B4

8-1/2" x 13" (FOOLSCAP)

A4

8-1/2" x 11" (LETTER)

B5

7-1/4" x 10-1/2" (EXECUTIVE)

A5

5-1/2" x 8-1/2" (INVOICE)

Size indication
with "R"

Landscape
orientation

Size indication
without "R"

Portrait orientation

dragonII_copy_sec.book  2 ページ  ２００６年１０月１８日　水曜日　午後７時３９分

Summary of Contents for MX-M550









































































































































































































Reviews:

No comments