Sharp MX-M550 Operation Manual Download Page 177

Page: 177 / 200

CALLING UP AND USING A FILE

7-19

Touch the [OK] key.

Touch the [PRINT AND DELETE THE
DATA] key or the [PRINT AND SAVE THE
DATA] key.

If the [PRINT AND
DELETE THE DATA] key
is touched, the files will
be automatically deleted
after printing.
If the [PRINT AND SAVE
THE DATA] key is

touched, the files will be saved after printing.
If there are no files that match the search
conditions, you will return to the file list screen.

CANCEL

PRINT AND DELETE THE DATA

PRINT AND SAVE THE DATA

NOTE

●

If "Auditing mode" is enabled in the administrator settings for copy mode, print mode, or document filing mode,
it will not be possible to perform batch printing of [ALL FILES].

●

To display the job tab of a mode for which "Auditing mode" is enabled in the administrator settings, the account
number must be entered.

dragonII_copy_sec.book 19 ページ２００６年１０月１８日　水曜日　午後７時３９分

Summary of Contents for MX-M550









































































































































































































Search results

Summary of Contents for MX-M550

Reviews:

Sharp MX-M550, Operation Manual, Page: 177 / 200

Search results

Summary of Contents for MX-M550

Reviews: