MX-FN10 ADJUSTMENTS 8 – 3
NOTE: In the MX-PNX5 series, when the punch hole type (destina-
tion) is set with the DIP switch, the F1-32 error display is
made. Note that the error display is made because of
mechanical reasons and that it is not an actual error in the
case of the MX-PNX5.
B. Punch unit and punch PWB sensor adjustment
1)
When the punch PWB is replaced, the following sensors must
be adjusted. (Punch dust detection must be executed in main-
tenance, too.)
Transport system, paper edge detection sensors
Punch timing sensor
Punch paper edge sensor 1
Punch paper edge sensor 2
Punch paper edge sensor 3
Punch paper edge sensor 4
Punch dust detection system
Punch dust sensor
2)
The adjustment of each sensor is performed with the DIP
switch and the push switch on the punch PWB.
3)
The DIP switch setting and the target adjustment sensors are
shown in the table below.
4)
Transport pass system, paper edge detection system sensor
adjustment procedures
a)
Check to confirm that the punch unit power is turned OFF.
b)
Check to confirm that there is no paper and interruption
material in the sensor section.
c)
Set the DIP switches 1, 2, and 3 to ON, then push and
hold the push switch and supply the power.
d)
Set all the DIP switches to OFF according to the table
above.
e)
Push the push switch and execute the adjustment. (The
LED flashes.)
f)
Check to confirm that the LED flashes (fixed state), and
turn OFF the punch unit power.
5)
Punch dust detection system sensor adjustment procedures
a)
Check to confirm that the punch unit power is turned OFF.
b)
Check to confirm that the dust box is normally set, and
that there is no punch dust in the dust box.
c)
Set the DIP switches 1, 2, and 3 to ON, then push and
hold the push switch and supply the power.
d)
Set the DIP switch 4 to ON and DIP switches 1, 2, and 3
to OFF according to the table above.
e)
Push the push switch and execute the adjustment. (The
LED flashes.)
f)
Check to confirm that the LED flashes (fixed state), and
turn OFF the punch unit power.
g)
Set all the DIP switches to OFF, and terminate the opera-
tion.
6)
Error display in case of an adjustment error
(Since the first cycle includes the first lighting of the LED, count
the number of flashing in the second cycle.)
LED flashing number
Kind of punch
4 times
2-hole type
9 times
2/3-hole type
7 times
4-hole type (France)
8 times
4-holel type (Sweden)
Adjustment execution sensor
DIP switch
1
2
3
4
Transport system, paper edge detection
system sensor (collective)
OFF
OFF
OFF
OFF
Punch dust detection system
OFF
OFF
OFF
ON
㪦㪥
㪈
㪉
㪊
㪋
㪚㪧㪬
㪣㪜㪛
㪧㫌㫅㪺㪿㩷㪧㪮㪙
㪛㪠㪧㩷㫊㫎㫀㫋㪺㪿
㪧㫌㫊㪿㩷㫊㫎㫀㫋㪺㪿
LED flashing number
Error content
14 times
Punch timing sensor adjustment error
15 times
Punch paper edge sensor 4 adjustment error
16 times
Punch paper edge sensor 3 adjustment error
17 times
Punch paper edge sensor 2 adjustment error
18 times
Punch paper edge sensor 1 adjustment error
19 times
Dust sensor adjustment error
20 times
Adjustment value save failure (error) to
EEPROM
21 times
Summary of Contents for MX-FN10
Page 52: ...Memo ...
Page 53: ...Memo ...
