Sharp MX-2300 G Installation Manual Download Page 56

Page: 56 / 88

MX-2300/2700 N/G MX-RBX1, MX-FNX2 8 – 7

3) Loosen four fixing screws of the adjustment section, and turn

the height adjustment screws on the front/rear sides to adjust
so that the clearances are even.

4) When the clearances are even, tighten the fixing screw of the

adjustment section, and install the foot cover.

F. Connector connection

1) Connect the finisher connector with the connector of the inter-

face pass unit, and tighten the screw.

Connect the finisher connector with the connector of the main
unit, and tighten the screw.

G. Staple position label attachment

Attach the label to the position indicated in the figure.
[For scanner] (package part No. 8)

[For RSPF] (package part No. 9)

Label attachment
reference

* Corner of the

"upper cabinet rear"

Corner R end fitting

Cleaning of the document scan section

CAUTION

When streaks appear on copy or scan
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).

Summary of Contents for MX-2300 G

























































































Search results

Summary of Contents for MX-2300 G

Reviews:

Related manuals for MX-2300 G

Brands by name

Popular brands

Sharp MX-2300 G, Installation Manual

Search results

Summary of Contents for MX-2300 G

Reviews:

Related manuals for MX-2300 G

Brands by name

Popular brands