MX-2300G/N, MX-2700G/N 1 – 14
5) Press [OK] key.
NOTE:
Do not cancel the simulation until "PLEASE QUIT THIS
MODE" is displayed.
6) Check the color balance and density.
Check to insure that the printed color balance check patch
image is within the following specifications.
The print density must be changed gradually from the lighter
level to the darker level. The density changing direction must
not be reversed.
The density level of each color must be almost at the same
level.
Patch B may not be copied.
Patch A must not be copied.
c. When the PCL mode is supported:
Execute SIM 64-5 to print the print test pattern.
Set each set value to the default and press [EXECUTE] key. The
print test pattern is printed.
The print density must be changed gradually from the lighter level
to the darker level. The density changing direction must not be
reversed. The density level of each color must be almost at the
same level.
d. When the PCL mode is not supported: (In the case of GDI
model)
Use SIM 67-25 to print the color balance adjustment sheet and
compare each process (CMY) black patch color balance and the
black patch to check the color balance.
The print density must be changed gradually from the lighter level
to the darker level. The density changing direction must not be
reversed.
The density level of each color must be almost at the same level.
Patch B may not be copied.
Patch A must not be copied.
M. Function and operation check
Check that the following operations are normal.
N. Setup and adjustment data recording
Print the various setup data and the adjustment data (list) with
SIM22-6 and keep the data.
• In case of a memory trouble, if the data are not kept, all the
adjustments must be made again.
• If the data are kept, the setup values and the adjustment values
can be entered without adjustments, shortening the servicing
time.
O. Necessary works before moving the machine
1)
If the following options are installed, remove all of them from
the machine.
• Saddle stitch finisher
• Large capacity tray
2)
Remove the following consumable parts from the machine.
• Paper
• Toner cartridge
• Development cartridge
3)
Lock the following sections.
• Scanner (Optical section)
• Paper cassette lift plate
NOTE: Since the hard disk drive is built in the machine, use care
not to exert vibrations or shocks to the machine when in
transit.
6
CLOSE
SIMULATION
NO.67-24
TEST
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
OK
0
CONFIRM THE ADJUSTED PATCH AND PRESS [OK] TO REGISTER THIS PATCH DATA
PRESS [REPEAT] TO CONTINUE THIS PROCEDURE.
REPEAT
CLOSE
SIMULATION
NO.67-24
TEST
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
0
CLOSE
COMPLETED THIS PROCEDURE.
PLEASE QUIT THIS MODE.
High density
Low density
Fig. 1 PG image
Max
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
C
M
Y
Bk
1) Max. density section
is not blurred.
3) Patch for each of C, M, Y, BK
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
2) Patch C or D of each of Y, C,
M, Bk is very slightly copied.
Patch A of Y, M, C, and
BK are not copied.
PRINTER CALIBRATION
Check items
Equipped condition
Key-in (operation panel)
Display (operation panel)
Paper feed
operation
Hand feed
Main unit paper
tray
Desk unit paper
feed tray
With the desk unit installed
Paper size detection
Originals size
detection
Original table
mode
RSPF mode
RSPF operation/
two sided copy
S-S mode
D-S mode
S-D mode
D-D mode
Bookbinding operation
With the finisher installed
Stapling operation
With the finisher installed
Grouping operation
With the finisher installed
Sorting operation
With the finisher installed
: Oct. 13 2006
6
Summary of Contents for MX-2300 G
Page 85: ...Memo ...
