manualshive.com logo in svg

Sharp MX-2300 G, Installation Manual

Share
Download
Sharp MX-2300 G Installation Manual Download Page 61

MX-2300/2700 N/G  AR-PN1A/B/C/D  9 – 4

10) Install the punch unit and fix it with the screws. Connect the

connector.

11) Connect the punch unit harness to the finisher PWB. 

Remove the clamp which is fixing the harness. Wire the har-
ness A (Purple) (package part No. 1) and the harness B
(Orange) (package part No. 2) as shown in the figure, and fix
them with the clamp. 

12) Open the top door, and install the right cabinet upper and fix it

with the screws.

13) Pass the interface harnesses (2 pcs.) through the rear cabinet

upper. While opening the upper door, install the rear cabinet
upper, and fix it with screws.

14) Install the front cabinet upper and fix it with the screws.

* Install the front cabinet upper so that the projection of the

latch arm is in the hole in the lock release lever. 

15) Install the knob and close the front cover.

Fixing
screw

Punch unit

Fixing screw

Fixing screw
(M4 x 6 with
tooth lock washer)

Boss

Boss

Boss hole

Boss hole

Harness A (Purple)

Harness B (Orange)

Clamp

CN14 on the PWB connected

Harness A (Purple)

Harness B (Orange)

Clamp

CN12 on the PWB connected

Upper cover

Fixing screw

Fixing screw

1

2

Summary of Contents for MX-2300 G

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands