Sharp LC-90Y8T Service Manual Download Page 42

Page: 42 / 67

LC-90Y8T

6 – 1

CHAPTER 6.

TROUBLESHOOTING

[1] Failure diagnosis by LED in front of cab-
inet

[1] Failure diagnosis by LED in front of cabinet

[2] LED flashing specification at the time of an error (Center icon LED used)

1. Display method

•

Since only the center icon LED can be used, slow flashing and fast flashing are combined.

•

After recovering from an error, if the same error cannot be generated again, refer to MONITOR ERR CAUSE on the adjustment process mode.

2. LED flashing method

Error flashing

Yes

Is the Center Icon flashing?

START

Is the Center Icon lighting

When AC plug on?

Is the Backlight lighting?

Check "[2] LED flashing specification at the time of an error (Center icon LED used)".

Check Power-Unit and AC-cable.

Check "

LED Backlight does not turn on.".

Check "

Picture does not display.".

1600ms

300ms

100ms

400ms

1600ms

OFF

Center icon

Summary of Contents for LC-90Y8T




































































Search results

Summary of Contents for LC-90Y8T

Reviews:

Related manuals for LC-90Y8T

Brands by name

Popular brands

Sharp LC-90Y8T, Service Manual

Search results

Summary of Contents for LC-90Y8T

Reviews:

Related manuals for LC-90Y8T

Brands by name

Popular brands