Sharp LC-90Y8T Service Manual Download Page 20 | Manualshive

Page: 20 / 67

background image

LC-90Y8T

5 – 3

2.3. Monitor microprocessor software version upgrade

Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.

Copy the file X I A N _Y8T_xxx.USB and XIANSUBxxx.SMB. (named temporarily) for monitor microprocessor software version upgrade to the
USB memory.

2.3.1 How to upgrade the software

1. Unplug the AC cord.

2. Insert the USB Memory for version upgrade into USB1.

3. Plug in the AC cord with power button pressed down.

4. After 5 seconds, unpress the power button.

CAUTION: •

The moment this operation is done, the upgrading of the monitor microprocessor software starts. While the upgrade is ongoing, never
power off the unit. Otherwise the upgrade will fail and the system may be serious damaged beyond recovery (inability to start).

•

After the monitor microprocessor software is upgraded, also perform the 'Industry Init'.

5. After the unit startup, the upgrade starts. The power led will blink continuously. Also, an upgrade screen will be shown during a minor upgrade.

6. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.

NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the

cause.

7. The upgrade success screen will be shown if upgrade screen was shown at 5.

8. Unplug the AC cord and remove the USB Memory for version upgrade.

9. Now the software version upgrade is complete.

NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-

itor microprocessor software version information and panel size information.

MAIN

SUB MICOM

PANEL EEPROM

3D IR MICOM

MAIN Version

SUB MICOM Version

PANEL EEPROM

3D IR MICOM Version

NO DATA

50%

NO DATA

0.820

90

Y8T

Software Update

MAIN

UPGRADE FAILURE

SUB MICOM

PANEL EEPROM

3D IR MICOM

MAIN Version

SUB MICOM Version

PANEL EEPROM

3D IR MICOM Version

NO DATA

SAME VERSION

NO DATA

90Y8T

Software Update

MAIN

UPGRADE SUCCESS

SUB MICOM

PANEL EEPROM

3D IR MICOM

MAIN Version

SUB MICOM Version

PANEL EEPROM

3D IR MICOM Version

NO DATA

100%

NO DATA

0.820

90Y8T

Software Update

«
...
18
19
20
21
22
...
»

Summary of Contents for LC-90Y8T




































































Reviews:

No comments

Related manuals for LC-90Y8T

Brand: Samsung Pages: 703

SyncMaster T23A750

Brand: Samsung Pages: 77

Brand: Samsung Pages: 588

Brand: Samsung Pages: 658

Brand: Samsung Pages: 2

Brand: Samsung Pages: 48

Series 9 9000 UN55C9000

Brand: Samsung Pages: 136

Brand: Samsung Pages: 8

Brand: Samsung Pages: 174

Brand: TCL Pages: 26

Brand: Walker Pages: 31

Brand: Palsonic Pages: 22

Brand: F&U Pages: 35

Brand: Magnasonic Pages: 8

Brand: Premier Pages: 105

Brand: Kogan Pages: 20

Brand: Naxa Pages: 31

Brand: Quasar Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands