Program name
Program
No
Description
Default
Parameters
Layout in 2 in 1
copy*
17
Selects a pattern for 2 in 1 copying.
Pattern 1
1(Pattern 1)
2(Pattern 2)
Layout in 4 in 1
copy*
18
Selects a pattern for 4 in 1 copying.
Pattern 1
1(Pattern 1)
2(Pattern 2)
3(Pattern 3)
4(Pattern 4)
Offset of paper
output tray
19
Enables or disables the offset function of the paper output tray.
The offset function can be specified respectively for the upper
and lower areas separated by an optional job separator tray kit.
Upper ON,
Lower ON
0(Upper OFF, Lower OFF)
1(Upper ON, Lower On)
2(Upper ON, Lower OFF)
3(Upper OFF, Lower On)
Image rotation in
duplex copying
20
Enables or disables image rotation (180˚) of the front side in one-
sided to two-sided copying or two-sided to one-sided copying.
OFF
0(OFF)
1(ON)
Location of the
margin*
22
Selects the location of the expanded margin.
Left
1(Left)
2(Top)
∗
These programs do not affect the copier functions unless certain optional equipment is installed.
2. Setting the user programs
1) Press and hold the light key for more than 5 seconds until all the
alarm indicators (
,
,
,
, and
) blink and "- -" ap-
pears in the copy quantity display.
2) Enter a program number using the numeric keys.
●
The selected program number will blink in the copy quantity dis-
play.
●
If a mistake is made in steps 2) to 4), press the CLEAR key.
The copier will return to step 2).
For example, to change the setting of the auto power shut-off timer,
press key 3.
3) Press the START key.
●
For programs 1 to 9 and 16 to 19, the entered program number
will be steadily lit on the left side of the copy quantity display
and the currently selected parameter number for the program
will blink on the right side.
●
For programs 10 to 15 (programs for auditing accounts), the
display varies with the program number.
4) Select the desired parameter using the numeric keys.
●
The entered parameter number will blink on the right side of the
copy quantity display.
●
The parameters are shown in the table below.
For example, to change the setting of the auto power shut-off timer to
60 min., press key 2.
∗∗
In European countries, the default setting of the preheat mode is 1
(30 sec.). For other programs, factory-default settings in these
countries are same to those shown above with an asterisk (
∗
).
Note: If you select "0" (OFF) in a program, the corresponding function
will be disabled.
5) Press the START key.
●
The right-hand number in the copy quantity display will be
steadily lit and the entered value will be stored.
6) To continue with other user programs, press the PRESS key and
then repeat steps 2 to 5. To exit the user program mode, press
the light key.
●
All the alarm indicators will go out.
3. Toner cartridge life
To find out the approximate quantity of toner remaining, follow the pro-
cedure below.
1) Press and hold the light key for more than 5 seconds until all the
alarm indicators (
,
,
,
, and
) blink and "- -" ap-
pears in the copy quantity display.
2) Press and hold the copy ratio display key for more than 5
seconds.
●
The approximate quantity of toner remaining will be indicated as
a percent in the copy quantity display. ("100", "75", "50", "25",
"10" or "LO" is displayed. When "LO" is displayed, the toner is
down to less than 10%.)
3) Press the light key.
●
All the alarm indicators will go out.
Patern A
Patern B
Patern A
Patern B
Patern C
Patern D
AR-162 USER PROGRAMS – 2