Sharp AR-121E Service Manual Download Page 91

Page: 91 / 138

(4) Features of copy density adjustment

For the copy density adjustment, the image data shift function
provided in the image process LSI is used.

List of the adjustment modes

Auto Mode

Brightness 1 step only

Manual Mode

Brightness 5 steps. Adjustment of only
the center brightness is made.

Photo Mode

Brightness 5 steps. Adjustment of only
the center brightness is made.

Manual T/S
mode

Brightness 5 steps. Adjustment of only
the center brightness is made.

T/S Auto
mode

Brightness 1 step only

(5) Copy density adjustment procedure

Use SIM 46-01 to set the copy density for each copy mode.
For selection of modes, use the copy mode select key.

A. Test chart (UKOG-0162FCZZ) setting

1) Place the test chart so that its edge is aligned with the A4

(Letter) reference line on the document table. Then place a
B4 (14

″

8 1/2

″

) white paper on the test chart and close the

document cover.

B. Perform the adjustment in each mode.

(1) Execute SIM 46-1.

(2) Select the mode to be adjusted with the exposure mode

select key. Set the exposure level to 3 for all adjustment.
(Except for the auto mode.)

Adjustment

mode

Exposure mode

display lamp

Ex-

posure

level

Sharp gray chart

adjustment level

Auto mode

Auto lamp ON

—

“3” is slightly
copied.

Manual

mode

Manual lamp ON

“3” is slightly
copied.

Photo mode

Photo lamp ON

“3” is slightly
copied.

Manual T/S

mode

Manual

lamp/Photo lamp

“4” is slightly
copied.

Auto T/S

mode

Auto lamp/Photo

lamp ON

“4” is slightly
copied.

(3) Make a copy.

Check the adjustment level (shown in the above table) of the
exposure test chart (Sharp Gray Scale).

Sharp Gray Scale adjustment level

Non toner

save mode

Toner save

mode

(When too bright): Decrease the value displayed on the

copy quantity display.

(When too dark): Increase the value displayed on the copy

quantity display.

* The value can be set in the range of 1 — 99.

Test chart

White paper

(1)

(2)

(1) Mode select key/display

lamp

(2) Exposure level select

key/display lamp

Slightly copied.

Not copied.

Slightly copied.

Not copied.

AL-1000/1010

9-9

Summary of Contents for AR-121E











































































































































Search results

Summary of Contents for AR-121E

Reviews:

Related manuals for AR-121E

Brands by name

Popular brands

Sharp AR-121E, Service Manual

Search results

Summary of Contents for AR-121E

Reviews:

Related manuals for AR-121E

Brands by name

Popular brands