manualshive.com logo in svg

Sharp AR-121E, Service Manual

Share
Download
Sharp AR-121E Service Manual Download Page 2

[1] GENERAL

The AR-121E/151E is the SRU model of the AR-120E/150E.
While the AR-120E/150E employs the drum replacement, the AR-121E/151E employs the developer replacement. Therefore, the display on the opera-
tion panel is changed from “      ” (drum) to “    ” (developer) accordingly.

1. Major functions

Item

CPM

SB/MB

2 Tray

SPF

R-SPF

FAX

GDI

with USB

GDI

without

USB

PCL

with USB

SOPM

Duplex

Model

AR-121E

12CPM

SB

Opt

AR-151E

15CPM

SB

Opt

Descriptions of items

CPM:

Copy speed (Copies Per Minute)

SB/MB:

SB = Manual feed single bypass, MB = Manual feed multi bypass 

2 tray:

Second cassette unit.

SPF:

Original feed unit

R-SPF:

Duplex original feed unit

FAX:

FAX function.

GDI with USB:

GDI printer function with USB.

GDI without USB:

GDI printer function without USB.

PCL with USB:

PCL printer function with USB.

SOPM:

Scan Once Print Many function (Many copies are made by one scan.)

Duplex:

Auto duplex copy function

Descriptions of table

: Standard provision
: No function or no option available

2. System Configuration

Options (AL-10PK/AL-11PK)

∗

 AR-150E, the memory has been already installed in the machine and is not supplied in the printer upgrade kit(AL-10PK).

(AR-121E)

(AR-151E)

Interface cable ... 1

(for IBM PC/AT or compatible computers)

Operation manual ... 1

Printer driver

(CD-ROM) ... 1

Screwdriver ... 1

Screws ... 4

Memory ... 1

∗

Printer board ... 1

AR-151E

1 – 1

Summary of Contents for AR-121E











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands