ShadeLab SHAN Instruction Manual Download Page 24 | Manualshive

Page: 24 / 32

background image

SHAN

I

INSTALLATION

–

REV 00

FITTING COVER PROFILE SUPPORTS

WARNING: Insert all cover profile supports onto the saddle profile.

COUPLING SADDLE /CASSETTE PROFILES

WARNING: Insert the saddle profile along with the cover profile supports on the cassette; for
projections higher than 3 m, partly unroll the fabric.
WARNING: insert the M6x16 screws (ref. 19) into the corresponding square nuts (ref. 20)

«
...
22
23
24
25
26
...
»

Summary of Contents for SHAN

































Reviews:

No comments

Related manuals for SHAN

Brand: Larry vs Harry Pages: 20

Brand: NEC Pages: 5

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: Napoleon Pages: 4

Brand: hager Pages: 4

Brand: PACIFIC CYCLE Pages: 112

Brand: E+E Elektronik Pages: 14

Brand: E+E Elektronik Pages: 26

Brand: E+E Elektronik Pages: 28

Brand: E+E Elektronik Pages: 2

Brand: BW Pages: 8

Brand: Labelmate Pages: 2

Brand: Labnet Pages: 2

5500DN - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

3600B - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: Viking Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands