background image

4

1. SAFETY

 

WARNING

This device can be used by children who are at least 8 years old 

and by people with reduced physical, sensory or mental capacities 

or those without knowledge orr experience, if they are properly 

supervised or if they have been given instrcutions on safely using 

the device and the associated risks have been understood. Children 

should not play with the device. Children should not clean or perform 

manintenance ont he device without supervision.

ELECTRICAL CONNECTIONS:

The electrical installation must be done by a qualified electrical engineer. 

The device's power supply must be connected to ground (class I) and protect-

ed by a high sensitivity differential circuit breaker (30 mA). Devices without 

plugs must be connected to a main switch on the power supply which discon-

nects all poles (contact separation distance of at least 3 mm). The connection 

must be used exclusively to provide the power to the product. 

If the power cord is damaged, to prevent possible danger, it must be replaced     

by the manufacturer, customer service team or a similarly qualified individual.

Labelling of notes in the operating instructions

    

  

Danger

This term defines a high risk of danger, which can lead to death or serious 
injury, if not avoided.

WARNING

Warning

This term defines a hazard which could cause a risk to the machine and its 
operation, if it is not taken into account

    

  

Dangerous area

This symbol characterises hazards that could lead to death or injury.

    

  

Dangerous voltage

This symbol characterises dangers associated with the voltage and provides 
information on voltage protection.

    

  

Property damage

This symbol, in combination with the keyword 

ATTENTION

, characterises 

dangers to the machine and its proper operation.

2. GENERAL INFORMATION

2.1 Areas of application

The single pump control system ZPS 1.3 is principally used for the regulation of liquid levels. For 

Summary of Contents for ZPS 1.3


















Reviews: