background image

12

2nd line on 

display

Signification

Alarm

Protocol 

signal

Fault pump 1

The motor current monitoring system has detected 

an exceedance of the set limit value and has shut 

down the pump motor.

Yes

IP1

Fault high water

The HW-sensor reports an alarm and switches on 

the pump. The HW-malfunction acknowledges itself 

when the turn-on level is reached.

Yes

HW

Fault I<3mA

The external sensor is selected, but the current 

is <3mA. There might be a disconnection, or 

the sensor might be defective. The malfunction 

acknowledges itself when the sensor current is 

within the normal range.

Yes

I<3mA

Fault SW

The floating switches are connecting in the wrong 

sequence (e.g. the lower floating switch is open 

when the upper floating switch closes). 

Yes

SW

Pump
Fault TH1
Fault TH2

Activation of the thermal control of the pump 

motor. The malfunction TH1 acknowledges itself 

after the motor has cooled down; TH2 has to be 

acknowledged manually.

Yes

Pump

TH1
TH2

Phase error

A phase of the power supply has failed.

Yes

Dreh

Fault ATEX

The ATEX mode is activated and the level is below 

the switch-off point of the selected pump.

Yes

Atex

Run-time alarm

The runtime monitoring of the pump has been 

exceeded 3 times in succession.

Yes

Time

3.2 Assembly and electrical connections

All electrical connections are to be established by an authorised 

professional only. Settings and adjustments on the control system 

as well as the commissioning of the control system are to be 

carried out by qualified persons only.

3.2.1 Mechanical fixation

The control system has to be fixed on an even surface. In order to fasten the control system, the 

housing cover has to be opened.

3.2.2 Mains connection

The left cable gland is intended for the cable entry of the mains cable. The separate cables are 

to be clamped into the spring terminals in the manner described below. According to the motor 

which is used, a single-phase or a three-phase connection can be established.

The power supply has to be secured by an independent all-pole 

fuse which can be switched off (max. 20 A).

    

  

    

  

    

  

    

  

    

  

    

  

Summary of Contents for ZPS 1.3


















Reviews: