SEW-Eurodrive MOVI-PLC basic DHP11B-T0 Manual Download Page 68

Page: 68 / 96

PROFIBUS-DP-V1 Functions

Structure of the DP-V1 parameter channel

Manual – MOVI-PLC

basic DHP11B.. controller

MOVILINK

return codes of
parameter setting
for DP-V1

The following table shows the return codes that are returned by the SEW DP-V1 inter-
face in case of an error in the DP-V1 parameter access.

MOVILINK

Return Code (hex)

Description

0x0810

Illegal index, parameter index does not exist in the unit

0x0811

Function/parameter not implemented

0x0812

Read access only

0x0813

Parameter lock activated

0x0814

Factory setting is active

0x0815

Value for parameter too large

0x0816

Value for parameter too small

0x0817

Reserved

0x0818

Error in system software

0x0819

Reserved

0x081A

Parameter access only via RS485 interface

0x081B

Parameter is access-protected

0x081C

Reserved

0x081D

Invalid value for parameter

0x081E

Factory setting was activated

0x081F

Reserved

0x0820

Reserved

0x0821

Reserved

0x0822

Reserved

0x0823

Reserved

0x0824

Reserved

0x0505

Incorrect coding of management and reserved byte

0x0602

Reserved

0x0502

Reserved

Summary of Contents for MOVI-PLC basic DHP11B-T0

































































































Search results

Summary of Contents for MOVI-PLC basic DHP11B-T0

Reviews:

Brands by name

Popular brands

SEW-Eurodrive MOVI-PLC basic DHP11B-T0, Manual

Search results

Summary of Contents for MOVI-PLC basic DHP11B-T0

Reviews:

Brands by name

Popular brands