8
Installing the Mounting Bracket
Locking Screw Installation
You must install the top leveling screws and the bottom locking
screws
before
you attach the mounting bracket to the back of
the flat panel. The top leveling screws consist of (2) 1/4-20 x
1-3/4” screws and the bottom locking screws consist of (2) 1/4-
20 x 1-1/8” screws.
Thread one (1) leveling screw into the top hole and one (1)
locking screw into the bottom hole on each of the mounting
brackets. Make sure the locking screw is securely threaded into
the mounting tab before proceeding.
Do not thread the screws any further once it is even with the
mounting tab. Threading the screws further will prevent you
from safely attaching the flat panel to the wall plate.
Attaching the Mounting Bracket to the TV
1. Place your TV screen side down on a soft, flat surface.
2. Identify the location of the VESA threaded inserts on the
back of your TV and align the holes in each mounting
bracket.
3. Secure each mounting bracket to your TV by inserting two (2)
screws per bracket.
Do not overtighten the mounting hardware.
Locking Screw Installation
Installing the Mounting Bracket (cont’d)
You must install the locking screws before you
panel. The locking screws consists of two (2) M6 x
120mm screws.
Thread one (1) locking screw into the bottom mounting
hole on each of the mounting brackets. Make sure the
locking screw is securely threaded into the mounting tab
before proceeding.
Do not thread the locking screw any further once
it is even with the mounting tab. Threading the
locking screw any further will prevent you from
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Locking Screw
Correctly Threaded
Locking Screw
Threaded Too Far
Security Barrel Installation (Optional)
Do not overtighten the locking screw.
Please read the following directions to install the
security barrel:
Remove the locking screw from the mounting
1.
2.
3.
4.
bracket.
Place the locking screw into and through the
security barrel (see illustration below).
Re-insert the locking screw and security
components into the mounting bracket.
Tighten the locking screw and security components
until seated in the mounting tab.
- PCB-CSL1 (sold separately)
- Padlock (Combination or Keyed; commercially
available)
Security
Barrel
Locking Screw
Do not thread the locking screw any further once
it is even with the mounting tab (see illustration to
the right). Threading the locking screw any further
panel to the wall plate.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Mounting Tab
Locking Screw
Correctly Threaded
Locking Screw Installation
Installing the Mounting Bracket (cont’d)
You must install the locking screws before you
panel. The locking screws consists of two (2) M6 x
120mm screws.
Thread one (1) locking screw into the bottom mounting
hole on each of the mounting brackets. Make sure the
locking screw is securely threaded into the mounting tab
before proceeding.
Do not thread the locking screw any further once
it is even with the mounting tab. Threading the
locking screw any further will prevent you from
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Locking Screw
Correctly Threaded
Locking Screw
Threaded Too Far
Security Barrel Installation (Optional)
Do not overtighten the locking screw.
Please read the following directions to install the
security barrel:
Remove the locking screw from the mounting
1.
2.
3.
4.
bracket.
Place the locking screw into and through the
security barrel (see illustration below).
Re-insert the locking screw and security
components into the mounting bracket.
Tighten the locking screw and security components
until seated in the mounting tab.
- PCB-CSL1 (sold separately)
- Padlock (Combination or Keyed; commercially
available)
Security
Barrel
Locking Screw
Do not thread the locking screw any further once
it is even with the mounting tab (see illustration to
the right). Threading the locking screw any further
panel to the wall plate.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Mounting Tab
Locking Screw
Threaded Too Far
P5080
T
Installation Instructions
Visit the Premier Mounts website
at http://ww
w.premiermounts.com
Page 3
Parts List
Installation
Tools
The following tools may be required depending upon your particular installation.
They are not included.
Pencil
Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket
Wrench
Phillips
Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/
8
˝
Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket
M10 Socket*
2
1
5
/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5
/16
˝
Flat
Washers
(Qty 6)
Pro Mounting Hardware
Universal
Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal
T
ilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX 920.857.9490
SCALE
REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
This section requires two people.
that the top and bottom hooks of both mounting
brackets are securely seated on the upper and
lower mounting rails of the wall panel.
mounting rails on the wall panel.
the wall.
Connect the top and bottom mounting brackets to
the rails of the wall plate.
Attaching the Flat Panel to the Wall Plate
This section assumes that you have read and
understood these sections:
●
Selecting the Proper Mounting Hardware
●
Universal Washer Installation
●
Universal Spacer Installation
surface.
1.
2.
3.
4.
1.
2.
3.
Identify the number and location of the thread
Align the holes on each mounting bracket with the
inserting a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Attaching the Flat Panel to the Wall
Plate” section.
Attaching the Mounting Bracket to the Flat Panel
