6
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 7
Installing the Wall Plate (cont’d)
Place the wall plate against the wall and align it with
the pilot hole.
®
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
Level the wall plate.
®
Use a pencil to mark the remaining five (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 7
Installing the Wall Plate (cont’d)
Place the wall plate against the wall and align it with
the pilot hole.
®
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
Level the wall plate.
®
Use a pencil to mark the remaining five (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 7
Installing the Wall Plate (cont’d)
Place the wall plate against the wall and align it with
the pilot hole.
®
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
Level the wall plate.
®
Use a pencil to mark the remaining five (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 7
Installing the Wall Plate (cont’d)
Place the wall plate against the wall and align it with
the pilot hole.
®
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
Level the wall plate.
®
Use a pencil to mark the remaining five (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
Installing the Wall Plate : Wood Stud Installation Cont.
P5080T
Page 8
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
The supplied
5
/
16
″ concrete wedge anchors must be
used for concrete installation.
You will need a
5
/
16
″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
Place the wall plate against the wall in the desired
viewing location.
®
Level the wall plate.
¯
Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
°
Set the wall plate to one side in a safe location.
Step 1
Use a power drill and
5
/
16
″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″ washer
into each pilot hole.
®
Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of
5
/
16
″
Concrete Drill Bit (Not Included)
>12”
>12”
Step 3
Drill a pilot hole in the center of the upper-right mark using a
1/4” drill bit
and power drill.
Step 6
Two people are recommended for this step: one person to level
the wall plate and another person to drill the pilot holes.
Drill a pilot hole in the center of each of the marks with a
power drill and a
1/4” drill bit.
Step 7
1. Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into each
pilot hole.
2. Tighten all lag bolts using a socket wrench and 1/2” socket.
Do not overtighten the lag bolts when attaching the mount to the wall.
Improper installation may result in personal injury or property damage.
Proceed to the “Installing the Mounting Bracket” section.
Step 4
1. Place the wall plate against the wall and align it with the
pilot hole.
2. Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into
the upper right mounting hole and tighten using a socket
wrench and 1/2” socket.
Do not overtighten the lag bolt.
Step 5
1. Level the wall plate.
2. Use a pencil to mark the remaining five (5) mounting
locations along the center of each wall stud.
