Setra Systems DATUM 2000 Operating Instructions Manual Download Page 10 | Manualshive

Page: 10 / 28

background image

10

Step 5.

Press the

HOLD/mode

key to display the number "0".

Note:

The decimal point that was set during calibration (CAL_U, CAL_C) will be

displayed.

Step 6.

Set the value you wish the meter to display at the presently applied pressure.

Press the

SCAN/adj

key to move the numbers up (+).

Press the

HOLD/mode

key to move the numbers down (-).

When the desired number is reached, press the SCAN/adj and HOLD/mode keys

at the same time. The number will flash repeatedly. Then, press the SCAN/adj key

to readjust the number or the HOLD/mode key to accept it. After the number is

accepted, the meter will display "bUSY" for 10 seconds and then resume normal

operation"

«
...
8
9
10
11
12
...
»

Summary of Contents for DATUM 2000





























Reviews:

No comments

Related manuals for DATUM 2000

Brand: Kawai Pages: 142

Brand: Kawai Pages: 10

Brand: C-LOGIC Pages: 4

Brand: E-line Pages: 164

Brand: ELGO Electronic Pages: 24

OPERA CONTROL CENTER SERVER - V 3.5

Brand: OPTICOM Pages: 21

Brand: Tohnichi Pages: 12

Concert Performer Series Digital Piano CP110

Brand: Kawai Pages: 149

Brand: horiba Pages: 175

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

Panametrics Aurora H2O

Brand: Baker Hughes Pages: 92

Brand: phase II Pages: 11

Brand: Agilent Technologies Pages: 20

Brand: MFJ Pages: 9

Brand: BAPI Pages: 3

SXP30 - ELECTRONIC PIANO

Brand: Technics Pages: 12

Xtrinsic MMA8491Q

Brand: Freescale Semiconductor Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands