Setra Systems DATUM 2000 Operating Instructions Manual Download Page 24

Page: 24 / 28

12.0 DATUM 2000

™

meter and manometer specifications

Display

Type

Light emitting diode

Color

Red

Height of digits

0.56 inch

Maximum readout

Reading rate

-9999 to +31999

2 to 3 times per second depending on input voltage

Overload signal (over range reading)

OVEr

Underload signal (under range reading)

UndEr

Polarity sign

Negative only

Brightness

Constant

Cutout dimensions

Meter

1/8 DIN: 1.77 in. x 3.62 in. (45 x 92 mm)

Manometer

1/4 DIN: 3.54 in. x 3.62 in. (90 x 92 mm)

Front panel
Meter

3.85 in. x 1.99 in. (98 x 50 mm)

Manometer

3.85 in. x 3.74 in. (98 x 95 mm)

Accuracy (readout only)

At 73°F (23°C)

±0.01%R ± 1 digit

At 60°F to 95°F (16° to 35°C)

±0.04%R ± 1 digit

Analog output

Transducers

Same as transducer output voltage

Transmitters

No analog output; the DATUM 2000™ terminates the

current loop

Physical

Operating temperature

32° to 130°F (0° to 55°C)

Storage temperature

-40° to185°F(-40° to 85°C)

Width

3.59 inches (91mm)

Height

Meter

Manometer

1.74 inches (91mm)

3.50 (89mm)

Electrical data

Power

Domestic

24 VDC (115 VAC 60 Hz 12 watt adapter provided w/-1 models)

Power cord length

6 feet (approx.)

Depth (incl. connector)

7 inches (178 mm)

(Allow at least 1/2" more for wires attached to terminal strip)

Summary of Contents for DATUM 2000





























Search results

Summary of Contents for DATUM 2000

Reviews:

Related manuals for DATUM 2000

Brands by name

Popular brands

Setra Systems DATUM 2000, Operating Instructions Manual

Search results

Summary of Contents for DATUM 2000

Reviews:

Related manuals for DATUM 2000

Brands by name

Popular brands