Servend Chillz Granitore 1 Service Manual Download Page 12

12

Installation and Service Manual

OPERATION

USE OF THE MACHINE

The machine you have purchased is intended to prepare granita and cold drinks.

MAIN COMPONENTS

The main components making up the machine are:

1.

Bowl lid

2.

Bowl locking device

3.

Thickness regulator

4.

Bowl

5.

Control panel

6.

Drip tray

7.

Grid

8.

Float (overflow indicator)

9.

Product dispenser

10. Product dispensing lever
11. Feet

To make the instructions easier to read, the following
abbreviations are used herein:

Granitore 1

 - a Granita machine with one (1) bowl;

Granitore 2 

- a Granita machine with two (2) bowls;

Granitore 3 

-a Granita machine with three (3) bowls;

Granitore 1 FF

 - identifies a Granita machine with one (1)

bowl and Fast Freeze refrigeration system;

Granitore 2 FF

 - identifies a Granita machine with two (2)

bowls and Fast Freeze refrigeration system;

Granitore 3 FF

 - identifies a Granita machine with three

(3) bowls and Fast Freeze refrigeration system.

1

10

9

2

3

4

5

7

6

11

8

TECHNICAL DATA

The technical data and features are listed below

Note: The manufacturer reserves the right to make
changes to the machine without notice.

Important! Any changes and/or additions of ac-
cessories must be explicitly approved and imple-
mented by the Manufacturer.

Model

Granitore 1

Granitore 1 FF 

Granitore 2 

Granitore 2 FF

Granitore 3 

Granitore 3 FF

Dimensions 
L x P x A - (cm).

27 x 52 x 81

42 x 52 x 81

67 x 52 x 81

Weight (kg)
(bowl empty)

29 

47

62

56

70

Maximum Electrical 
Input (W)

See rating plate on side of machine

Operating voltage 
(V). 

Operating temperature.

Min. 20°C

Max. 32°C

Number of bowls.

1

2

3

Capacity of each
bowl (l.)

12

Sound pressure level 

<< 70 dB

A

Class.

N

A

P

L

Summary of Contents for Chillz Granitore 1









































Reviews: