background image

KIT/45

  84.45  

CONTROL KIT OF ONE 24 VDC PARKING SPACE SAVER MOTOR

D

AL

  1

96

5

Pag. 1/7

K

IT

/4

I E

Thank you for having chosen SERAI ELETTRONICA, certain that you will obtain the performance necessary for use 
from this product.
Remember that you are about to install a 

system

 classified as "motorised activation destined to move gates and 

automatic doors in commercial and residential buildings, with access of vehicles and persons", which is considered 
as 

potentially dangerous

. Normally, it is your task and responsibility to make this system "safe" for how much this is 

reasonably possible

Installation and maintenance of such a system must therefore by carried out exclusively by 

trained, qualified and 

expert staff

, with 

"state-of-the-art" executions

, as prescribed by DM 37/08 and subsequent amendments and 

integrations. 

The law prohibits the realisation of these types of plants by unqualified staff

On realisation of its own products, SERAI has respected the following:

Reference Directives for CE marking

:

machinery: 2006/42/EEC
low voltage: 

2006/95/EEC

electromagnetic compatibility: 

2004/108/EEC

General reference Standards

:

electrical safety: 

IEC EN60335-1 + IEC EN60335-2-103

electromagnetic compatibility - emissions:

IEC EN61000-6-3

electromagnetic compatibility - immunity: 

IEC EN61000-6-1

When installing the system, as well as that mentioned previously, please respect the following.

General reference Standards

safety of electrical plants in general environments: 

IEC 64-8 V2

The SERAI products allow to implement systems that comply with these Standards. The following is very 
important as 

THE INSTALLER IS RESPONSIBLE FOR THE SYSTEM AND ITS FUNCTIONING IN 

COMPLIANCE WITH STANDARDS.

This manual must be read completely before proceeding with installation of the various parts of the plant

.

.

 .

!

INSTALLER MANUAL

TYPICAL PLANT EXAMPLE

KIT COMPONENTS:

MP/30 motor
CR/53 control unit
OG/64 remote control

M I 

O

M I 

O

P A

 R K

P A

 R K

1
2
3

1

2
4

3

ACCESSORIES

2xBT/20: 12V 2Ah batteries 
-optionals-

4

E

R

A

I

S

GATE OPENER DIVISION

Summary of Contents for KIT 45








Reviews: