Sentinel XL S-4000 User Instruction Manual Download Page 10

Page: 10 / 36

ECO: 102-0461-01

S-4014

Rev B

REPLACEMENT PARTS

Part No.

Component

Cartridges and Plug

S-4002

HE-High Efficiency Particulate Air (2 per package)

S-4012 (Optional)

OV/CD/CL/HC/HF/SD/HE Cartridge(3 per package)

S-4006

Blower Plug (with knob); used w/ S-4002 filters only

S-4007 (Optional)

Blower Plug (flat)

S-4008 (Optional)

Blower Flat Plug Installation and Removal Tool

Battery Packs and Charger

S-2003

Rechargeable NiMH Battery Pack

S-2004 (Optional)

Non Rechargeable LiMnO2 Battery Pack

S-2009

Fast Battery Charger (with Instructions)

S-4013 (Optional)

Alkaline Battery Adapter

Blower

S-2002

Standard Blower

Breathing Hose

S-4005

33” Long Breathing Hose

S-4003 (Optional)

25” Long Breathing Hose

Hood

S-3101

Sentinel XL™ Clear Hood

Waist Belt

S-4011

Decon and Quick Release Belt and Clip

Flow Meter

S-2010

Flow Meter

Instruction Manual

S-4014

Sentinel XL™ HP Clear Hood User Instruction Manual

Summary of Contents for XL S-4000





































Search results

Summary of Contents for XL S-4000

Reviews:

Related manuals for XL S-4000

Brands by name

Popular brands

Sentinel XL S-4000, User Instruction Manual

Search results

Summary of Contents for XL S-4000

Reviews:

Related manuals for XL S-4000

Brands by name

Popular brands