Sentinel XL S-4000 User Instruction Manual Download Page 2

Page: 2 / 36

ECO: 102-0461-01

S-4014

Rev B

∆

WARNING

IMPROPER USE OF THIS HOOD AND RESPIRATOR MAY RESULT IN

PERSONAL INJURY OR DEATH. IMPROPER USE INCLUDES, BUT IS

NOT LIMITED TO, USE IN ATMOSPHERES CONTAINING UNKNOWN

CONTAMINATES AND/OR UNKNOWN CONCENTRATIONS OF

CONTAMINANTS, USE WITHOUT ADEQUATE TRAINING,

DISREGARD TO THE WARNINGS AND INSTRUCTIONS CONTAINED

HEREIN AND FAILURE TO INSPECT AND MAINTAIN THIS

RESPIRATOR.

THE HOOD AND RESPIRATOR IS NOT INTENDED FOR USE IN

ATMOSPHERES WHERE THE IDENTITY AND/OR CONCENTRATION

OF THE CONTAMINANT IS UNKNOWN. THIS MAY RESULT IN

IMMEDIATE DANGER TO PERSONNEL.

THIS HOOD AND RESPIRATOR DOES NOT SUPPLY OXYGEN AND

MUST NOT BE USED IN OXYGEN DEFICIENT ATMOSPHERES

CONTAINING LESS THAN 19.5% OXYGEN.

∆

WARNING

TRAINING IS REQUIRED BEFORE USE OF THIS HOOD AND

RESPIRATOR. FOLLOW THESE INSTRUCTIONS CAREFULLY. THIS

POWERED AIR PURIFYING DEVICE IS ONLY FOR USE IN SPECIFIC

ATMOSPHERES AND UNDER CERTAIN CONDITIONS. USE OF THIS

RESPIRATOR WITHOUT PROPER TRAINING COULD RESULT IN

SERIOUS INJURY OR DEATH.

Summary of Contents for XL S-4000





































Search results

Summary of Contents for XL S-4000

Reviews:

Related manuals for XL S-4000

Brands by name

Popular brands

Sentinel XL S-4000, User Instruction Manual

Search results

Summary of Contents for XL S-4000

Reviews:

Related manuals for XL S-4000

Brands by name

Popular brands