Seneca T201DCH100-M User Manual Download | Manualshive

Page: 6 / 20

background image

User Manual

T201DCH50/100/300-M

ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY

Doc. MI004730-EN

Rev. 1.0.2

Page 6

CONFIGURING THE DEVICE

The Device can be configured in two ways:



A configuration from dip switches



A full configuration from flash (using Easy Setup Software)

WARNING!

Dip switches configuration are active only after a reboot!

WARNING!

The Dip Switch setting will overwrite the Flash setting so, if you need to use the flash configuration

you MUST set ALL dip switches to “OFF”.

BE REPRODUCED WITHOUT PRIOR PERMISSION.

«
...
4
5
6
7
8
...
»

Summary of Contents for T201DCH100-M





















Reviews:

No comments

Related manuals for T201DCH100-M

Brand: WDS Pages: 32

Brand: Transition Networks Pages: 1

Brand: Scosche Pages: 4

Brand: DB Elettronica Telecomunicazioni Pages: 19

Brand: Icom Pages: 64

Brand: H-ITT Pages: 2

Orion Universal 1 Transmitter

Brand: Badger Meter Pages: 2

Brand: SEIKAKU TECHNICAL GROUP Pages: 6

Brand: Talitor Pages: 5

Brand: Sailor Pages: 104

Brand: Intek Pages: 40

Brand: Magnum Pages: 8

Brand: Midland Pages: 36

ALAN 48 PLUS MULTI B

Brand: Midland Pages: 52

Brand: Salcom Pages: 4

Brand: Sailor Pages: 2

Brand: Visonic Pages: 2

Brand: Visonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands