background image

 

User Manual

 

T201DCH50/100/300-M 

 

 

ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY 

Doc. MI004730-EN

 

Rev. 1.0.2 

Page 2 

 

Introduction 

Contents of the present documentation refer to products and technologies described in it.  
All technical data contained in the document may be modified without prior notice. 
Content of this documentation is subject to periodical revision. 
To use the product safely and effectively, read carefully the following instructions before use.  
The  product  must  be  used  only  for  the  use  for  which  it  was  designed  and  built:  any  other  use  must  be 
considered with full responsibility of the user.  
The installation, programming and set-up is allowed only to authorized operators, physically and intellectually 
suitable. 
Set up shall be performed only after a correct installation and the user shall perform every operation described 
in the installation manual carefully.  
Seneca  is  not  considered  liable  for  failure,  breakdown,  accident  caused  because  of  ignorance  or  failure  to 
apply the indicated requirements.  
Seneca is not considered liable for any unauthorized changes.  
Seneca reserves the right to modify the device, for any commercial or construction requirements, without the 
obligation to promptly update the reference manuals. 
No liability for the contents of this documents can be accepted.  
Use the concepts, examples and other content at your own risk.  
There may be errors and inaccuracies in this document that may of course be damaging to your system.  
Proceed with caution, and although this is highly unlikely, the author(s) do not take any responsibility for that.  
Technical features subject to change without notice. 
 

CONTACT US

 

 

Technical support 

[email protected]

  

Product information 

[email protected]

 

 
 
Document revisions 

DATE 

REVISION 

NOTES 

19/07/2017 

1.0.0 

First revision. 

26/10/2017 

1.0.1 

Added info for Reset Imin/imax commands. 

22/01/2018 

1.0.2 

Changed Accuracy info. 

 

 

 

 

 

 

 
This document is property of SENECA srl. Duplication and reproduction are forbidden, if not authorized.  
 
 

BE REPRODUCED WITHOUT PRIOR PERMISSION.

 

Summary of Contents for T201DCH100-M





















Reviews: