background image

 

User Manual

 

T201DCH50/100/300-M 

 

 

ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY 

Doc. MI004730-EN

 

Rev. 1.0.2 

Page 10 

 

 

WARNING!

 

Dip switches configuration is active only after a reboot! 

 

 
So, for example using the RMS measure with 0 A input the Output voltage is 0V but using the Bipolar measure 
with 0 A input the Output voltage is 5V. 
 

 

MODBUS RTU PROTOCOL 

 
The Modbus protocol supported by the T201DCH50-100-300 is: 
 

 

Modbus RTU Slave  
 

For more information about these protocols, please refer to the Modbus specification website:  
 

http://www.modbus.org/specs.php

 
 

4.1.

 

Modbus RTU function code supported 

The following Modbus RTU functions are supported: 
 

 

Read Holding Register  

(function 3)  Max 5 Registers 

 

Write Single Register  

(function 6) 

 

Write Multiple registers  

(function 16) Max 2 Registers 

 

WARNING!

 

All 32 bits values are stored into 2 consecutive registers 

 
 

WARNING!

 

You can Read a Maximum of 5 Modbus Registers with the Read Holding Register function (function 3) 

BE REPRODUCED WITHOUT PRIOR PERMISSION.

 

 

 
 
 

Summary of Contents for T201DCH100-M





















Reviews: