⑧Remarks on after-sales servicing
･ If the watch requires service, take it to the retailer from whom
the watch was purchased. If the trouble occurs within the
guarantee period, submit the certificate of guarantee together
with the watch.
･ For repair after the guarantee period or for any other
information regarding the watch, contact the retailer from
whom the watch was purchased or the "SEIKO S-YARD CO.,
LTD.".
･ Guarantee coverage is spelled out in the certificate of
guarantee. Please read it carefully and keep the certificate
for ready reference.
⑦Remarks on replacement parts
･ SEIKO makes it policy to usually keep a stock of spare parts for
its watches for 7 years. In principle, your watch can be
reconditioned within this period if used normally. (Replacement
parts are those which are essential to maintaining the functional
integrity of the watch.)
･ The number of years that a watch is considered repairable
may vary greatly depending on the conditions under which
it was used, and normal accuracy may not be achieved in
some cases. We recommend, therefore, that you consult
the retailer from whom the watch was purchased when
having them repair your watch.
･ The case, dial, hands, glass and bracelet, or parts there of
may be replaced with substitutes if the originals are not
available.
●When used with the pouch:
●When used with the shoulder
strap for the printer.
Velcro band
Connecting cord
⑨Accessories
■
6
TROUBLESHOOTING GUIDE
Problem
Possible cause
Solution
Problem
Possible cause
Solution
The motor does not run
even if the power switch of
the printer is turned "ON".
The
paper
is
not
advanced by pressing the
paper advancing switch.
By pressing the start
button,
the
paper
is
advanced, but the printed
digits
or
letters
are
detective or the data are
not printed at all.
●Weak batteries.
●The batteries are not
installed properly.
●The paper is stuck.
●Weak batteries.
●The paper is stuck.
●The roll paper gets out
of shape.
●The cord is not
connected properly.
●Water or foreign matters
are sticking to the cord
plug.
●The paper is not set
properly.
●Replace the battery with
new ones.
●Install the batteries
properly.
●Remove the paper.
●Replace the battery with
new ones.
●Remove the paper.
●Make the roll paper
round.
●Connect the cord
correctly.
●Wipe off the water or
foreign matters.
●Inset the paper
properly.
By pressing the start
button, the data are
printed out, but the paper
is not advanced or is
advanced irregularly.
By pressing the start
button, no data are printed
out and the paper is not
advanced at all.
●The paper is stuck.
●Weak batteries.
●Weak batteries.
●The batteries are not
installed properly.
●The power switch of the
printer is not set to
"ON".
●The cord is not
connected properly.
●Water or foreign matters
are sticking to the cord
plug.
●Remove the paper.
●Replace the batteries
with new ones.
●Replace the batteries
with new ones.
●Insert the batteries
correctly.
●Turn the power switch
"ON", and then press
the start button.
●Connect the cord
properly.
●Wipe off water or
foreign matters.
※If your stopwatch and printer will not operate properly despite the solutions in the table, take them to the retailer from whom your stopwatch was purchased for repair.
Before requesting service, please check your stopwatch following the table below.
■
7
SPECIFICATIONS (STOPWATCH S143)
1. Frequency of crystal oscillator …………………………………32,768Hz (Hz＝Hertz…Cycles per second)
2. Loss/gain (monthly rate) ………………………………………Less than 15 seconds at normal temperature range (5℃〜
35℃)
3. Operational temperature range …………………………………−10℃〜＋60℃
Desirable temperature range of usee …………………………０℃〜＋50℃
4. Display system ……………………………………………………Measures up to 10 hours. Hour, minutes, seconds, 1/100
seconds, tnree-row display of split time/lap time/total elapsed
time or lap time in progress. No. of blocks, no. of split times (0
〜999), 300 memory recall, BLOCK, SPLIT, LAP, STOP,
RECALL, stopwatch marks, memory indicator, BATT.
5. Time/calendar display ……………………………………………Hour (24hour indication), minutes, seconds, year, month, date
and calendar mark. ID no. (OFF/01〜99), contrast adjustment
display.
6. Display medium …………………………………………………Nematic Liquid Crystal, FEM (Field Effect Mode)
7. Battery ……………………………………………………………Lithium battery SB-T74, 1 piece
8. Battery Life ………………………………………………………A new normal battery will last approximately three years.
※If the stopwatch is used for more than 3 hours a day, the battery life
may be less than 3 years.
9. IC (Integrated Circuit) ……………………………………………C-MOS-LSI, 1 piece
※The above specifications are subject to change without prior notice, for product improvement.
10. Battery life indicator ………………………………………………"BATT" mark start flashing when the battery life nears its end.
