Seiko MPU-L465 Series User Manual Download Page 45 | Manualshive

Page: 45 / 55

background image

-

42

-

■

Bluetooth-based Wireless Transmission (Bluetooth-mounted Printer)

(1) Power the printer off.

(2) Select a transmission method to be used. See Section 7, Function Settings, for details.

(3) Power the printer on and send data from the host computer to the printer.

(4) Verify that the data is correctly printed.

Hint



The maximum distance of transmission is approx. 10 m.

The maximum distance of transmission may differ depending on the radio interference

and environment.

WARNING



The printer may affect medical or other electronic devices. Obtain information and

data concerning influence due to radio interference from the respective

manufacturers or dealers.



When using the printer in medical institutions, follow their guidelines.



Turn the printer off in an airplane for safety.



DO NOT use the printer in any area or district where its use is probibited.

«
...
43
44
45
46
47
...
»

Summary of Contents for MPU-L465 Series
























































Reviews:

No comments

Related manuals for MPU-L465 Series

Brand: V-King Pages: 41

Brand: QMS Pages: 26

Brand: DataCard Pages: 2

Brand: Felix Storch Pages: 41

Brand: Olivetti Pages: 20

Brand: Olivetti Pages: 63

Brand: Olivetti Pages: 180

Brand: Olivetti Pages: 118

Brand: Olivetti Pages: 80

Brand: Olivetti Pages: 253

Brand: Olivetti Pages: 163

d-COLOR MF222plus

Brand: Olivetti Pages: 151

Brand: Olivetti Pages: 176

WorkCentre XD Series

Brand: Xerox Pages: 63

Brand: Tally Pages: 266

Brand: Xerox Pages: 20

Brand: Olivetti Pages: 149

Brand: NBS Technologies Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands