Seiko MPU-L465 Series User Manual Download Page 23

Page: 23 / 55

(7) Battery rubber cover

This cover is used to mount and secure the battery

pack. Open the rubber cover and then attach and

detach the battery pack.

(8) Battery release lever

This lever is used to remove the battery pack from

the printer.

(9) Paper cover open lever

This lever is used to open the paper cover in order

to install the paper.

(10) Paper outlet port

This is a paper outlet port equipped with a paper

cutter.

(11) Paper guide unit

This unit is used to install paper. Paper with

various width can be installed.

(12) Paper guide

This guide releases the paper guide lock via lever

(13) according to the paper width and changes the

paper guide width. By attaching and detaching

adapters to it, it is possible to fit several types of

inner diameter.

(13) Paper guide lock lever

This lever is used to release the paper guide lock

when changing the position of the left and right

paper guides.

(14) Thermal printhead

This printhead prints characters on the paper. Be

careful that It reaches a high temperature just after

printing.

(15) Paper sensor

This sensor detects “no paper “and “timing-mark.”

(16) Paper cutter

This unit cuts paper.

(17) Roller Cover Open Lever

This lever is used to open the roller cover when

setting the stripping paper in use of the label

peeling function.

(18) Stripping Paper Outlet port

The stripping paper is outlet when the label

peeling function is used.

(19) Stripping Paper Cutting Sub Blade

This blade is used as an auxiliary blade when

cutting excess stripping paper in use of the label

peeling function.

Summary of Contents for MPU-L465 Series
























































Search results

Summary of Contents for MPU-L465 Series

Reviews:

Related manuals for MPU-L465 Series

Brands by name

Popular brands

Seiko MPU-L465 Series, User Manual

Search results

Summary of Contents for MPU-L465 Series

Reviews:

Related manuals for MPU-L465 Series

Brands by name

Popular brands