Seiko MPU-L465 Series User Manual Download Page 47 | Manualshive

Page: 47 / 55

background image

-

44

-

■

Charging by a Dedicated Battery Charger (Optional Unit)

Dedicated battery charger

Follow the steps shown below to charge:

(1) Connect the AC cable to the battery charger.

(2) Put the AC cable plug into the inlet.

(3) Mount the battery pack on the battery charger so that the electrodes of the battery pack can be

aligned with the metallic terminals of the battery charger.

(4) The CHARGE lamp on the battery charger lights red to start charging.

(5) The CHARGE lamp changes to green when the battery is fully charged.

(6) Remove the battery pack after charging is completed.

(7) Unplug the AC cable from the inlet.

AC cable

Battery charger

Battery pack

«
...
45
46
47
48
49
...
»

Summary of Contents for MPU-L465 Series
























































Reviews:

No comments

Related manuals for MPU-L465 Series

Brand: Felix Storch Pages: 39

Brand: Felix Storch Pages: 10

RS/6000 44P Series 270

Brand: IBM Pages: 216

Brand: Xerox Pages: 13

Brand: Xerox Pages: 16

Brand: Lanier Pages: 298

6130N - Phaser Color Laser Printer

Brand: Xerox Pages: 2

6130N - Phaser Color Laser Printer

Brand: Xerox Pages: 2

Brand: Chamiin I&C Pages: 18

Brand: Oki Pages: 2

ApeosPort-III C7600

Brand: Xerox Pages: 369

Brand: Wang Pages: 181

Brand: Mitsubishi Pages: 2

Brand: Jolimark Pages: 65

WorkCentre 7970

Brand: Xerox Pages: 268

Brand: Oki Pages: 78

Brand: Citizen Pages: 255

ColorQube 9303 Series

Brand: Xerox Pages: 1812

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands